Paper Tensile Strength Testers: Which Grips and Load Cells Do You Need?

Paper Tensile Strength Testers: Which Grips and Load Cells Do You Need?

Choosing the right paper tensile strength tester involves more than comparing load capacity and test speed. Grip design, jaw surfaces, and load cell range can all affect specimen alignment, prevent slippage or damage, and influence measurement accuracy. Matching these components to paper properties and the applicable test method is essential for reliable, repeatable results. The best configuration for a lightweight tissue, for example, may be a poor choice for a stiff packaging board.

The useful question is not simply, “Will this machine break the sample?” It is whether the machine can hold the specimen without changing the failure, measure force accurately across the expected range, and produce results that are comparable with the laboratory’s chosen method.

Start with the paper, the test method, and the expected force

Before requesting a quotation, define the materials and results the laboratory needs to cover. A paper mill checking one grade of writing paper has a different problem from a packaging laboratory testing several papers, boards, and paper-based laminates. The latter may need interchangeable grips or more than one load cell rather than a single compromise setup.

List the specimen widths, thicknesses, machine-direction and cross-direction requirements, and expected breaking forces. Also identify whether the laboratory reports only maximum tensile force or needs tensile strength, elongation, tensile energy absorption, or tensile index. These outputs do not all place the same demands on displacement measurement, specimen preparation, and software calculations.

Relevant methods include ISO 1924-2 for paper and board tensile properties using a constant-rate-of-elongation apparatus, and TAPPI T 494 for tensile properties of paper and paperboard. Do not assume that a machine advertised as suitable for one method automatically satisfies every requirement of the other, or every edition of either. Confirm the applicable edition, specimen preparation, conditioning, test settings, and calculation rules for the work being performed.

Choose grips by how the specimen behaves, not by appearance

A grip has two jobs that compete with each other: hold the strip firmly enough to prevent movement, but gently enough to avoid creating the failure. Jaw width, face material, pressure, alignment, and the way pressure is applied all matter. A clean-looking break is useful evidence, but it is not proof on its own that the grip is suitable.

Pneumatic grips: useful control, but not automatic suitability

Pneumatic grips are worth considering when operators test many specimens or need more consistent clamping between shifts. Adjustable pressure can help when the laboratory moves between paper grades. They also reduce the dependence on how tightly each operator turns a screw.

That consistency depends on the actual grip design and air supply. Pressure that works for a robust paper may crush a softer sheet; reducing pressure too far can allow slip. Ask how the pressure is adjusted and verified, what air supply is required, and whether the grip maintains even contact across the specimen width. A pneumatic label alone does not answer those questions.

Manual grips: practical for narrower workloads

Screw-operated or other manual grips can be a sensible choice for a laboratory with modest throughput and a limited material range. They are relatively straightforward to operate, but the clamping force can vary with the operator. That matters most when a sample sits close to the boundary between slipping and being damaged by the jaws.

If manual grips are under consideration, include more than one operator in the evaluation. A setup that works only when its most experienced user tightens the jaws is not yet a robust routine method.

Jaw faces often decide whether the result is believable

Smooth, textured, serrated, and compliant faces each solve different problems. More aggressive surfaces can improve holding on difficult materials, but they can also mark or cut the specimen. Smooth metal faces may avoid deep impressions yet slip on some coated papers. Compliant facings can distribute pressure more gently, although their condition changes with wear and contamination.

For thin or delicate paper, begin by examining whether the faces make uniform contact without a sharp pressure line. For coated or glossy stock, pay particular attention to movement at the jaw. Stiff board presents another issue: the grips need sufficient opening and face geometry to hold it squarely without bending the strip at the entry point.

Paper-based laminates deserve their own trial. Their layers may respond differently to clamping, and a surface that holds the outer layer may still allow local damage or separation. Do not assume that the jaw face selected for uncoated paper will be appropriate for a coated or multilayer packaging material.

Inspect specimens after testing. Repeated breaks at the jaw edge, crushed zones, visible sliding marks, or unusually scattered elongation results justify investigation. They do not automatically prove that the grips are at fault: damaged cut edges, misalignment, material defects, and conditioning can produce misleading patterns too. Check these possibilities before changing the entire fixture.

Size the load cell around the forces you will actually measure

A larger load cell is not automatically a safer choice. It may protect against overload on stronger samples, but the force produced by weaker papers can fall near or below the cell’s verified measurement range. Conversely, a small cell may resolve low forces well but be vulnerable when a stronger specimen or unexpected peak is applied.

Use expected breaking force, not paper grammage alone, to narrow the choice. If tensile strength is known in force per unit width, multiply it by the intended specimen width to estimate breaking force. For tensile index, the estimate also depends on grammage and consistent units. These are planning estimates, not substitutes for trial measurements; variation between grades and directions must be considered.

An illustrative calculation shows the logic. If a material is expected to break at 4 kN/m and the specimen is 15 mm wide, the estimated peak force is 60 N. The selected cell must measure that force within its specified and calibrated range, while leaving appropriate capacity for stronger specimens and unexpected peaks. The example is arithmetic, not a recommended setting or a claim about a particular paper grade.

Ask for the force accuracy specification as a function of reading and range, not just a headline percentage. Resolution is not the same as accuracy: a display can show fine increments even when performance at the low end has not been verified. Request the calibration scope and confirm that the forces relevant to your tests are covered.

Where the material range is wide, two interchangeable cells may be more defensible than one oversized cell. Check how easily they can be changed, whether the software identifies the installed cell, and what calibration or verification steps are needed after a change. Also ask about overload protection and the weight of the grips supported by the measurement system; both can affect the practical configuration.

Alignment and elongation need separate attention

A suitable load cell cannot compensate for a strip pulled at an angle. Misaligned jaws introduce uneven loading across the specimen, which can cause premature edge failure or increase result scatter. The issue can be especially difficult to spot with narrow strips: the machine may still generate a plausible force curve.

Check that the grip faces are parallel, centered on the loading axis, and appropriate for the specimen width. Specimen guides can make positioning more repeatable, provided they do not constrain or damage the test piece. The distance between the grips must also be set and verified according to the selected method.

If elongation is a reported result, establish what the instrument actually measures. Crosshead movement is not necessarily identical to specimen extension: grip seating, slip, and deformation of the load train can contribute to the reading. Ask the supplier how displacement is measured and whether the arrangement meets the requirements of the chosen method. A convincing peak-force result does not by itself validate elongation or energy calculations.

Make the supplier demonstrate the difficult samples

A useful evaluation uses representative material at both ends of the intended range, not just the sample that is easiest to test. Include the weakest grade, a stronger grade, and any coated, delicate, or stiff material that could challenge the grips. Prepare and condition specimens consistently with the applicable method, and record the direction of each strip.

During the trial, look beyond the average breaking force. Review individual force-extension curves, the location and appearance of breaks, variation between replicates, and signs of movement in the jaws. If results change substantially when clamping pressure is adjusted, the setup may be sensitive to operator practice. That is valuable information before purchase, not a nuisance to explain away afterward.

Ask for a written configuration that identifies the load cell, grip bodies, jaw faces, specimen-width capability, pressure requirements where relevant, and the measurement ranges covered by calibration. Confirm what is included for routine verification, replacement jaw faces, software calculations, and service. If testing will extend beyond paper to plastic packaging or barrier materials, establish which additional fixtures or cells are needed rather than assuming the paper setup will cover them.

Paratronix Instruments Co., Ltd. develops and supplies packaging testing instruments for applications including pharmaceutical packaging, plastic packaging materials, and high-barrier materials. For a mixed-material laboratory, that broader packaging context is useful when discussing a testing solution—but the proposed configuration should still be assessed against the actual specimens, methods, and force ranges.

Before placing an order, settle the grip and load cell choices together. A cell with excellent low-force capability is of little use if the jaws slip, while a grip that holds every strip by crushing it will not produce representative paper data. Keep the trial specimens and force curves with the purchasing record; they provide a practical reference when the instrument is installed and when future materials are added.

NEXT:Already the last page

Leave A Reply

Submit